Tips: Due to the wide variety of air compressors, it may not be possible to display them all on the website. If you need any, please contact us by email or phone.
Product Description
Part number JRZ‑20AZ/0.8 is oil‑injected single‑stage fixed‑speed (power‑frequency) direct‑drive rotary screw air compressor, rated motor power 15 kW, nominal free‑air delivery 2.3 m³/min at 0.8 MPa working pressure, air‑cooled design. Direct flexible‑coupling transmits torque between motor and screw air‑end. It is designed for small‑and‑medium‑size industrial sites with relatively stable continuous compressed‑air consumption.
Critical technical clarification: This is oil‑injected screw compressor unit. It outputs compressed‑air with residual oil content. It CANNOT directly supply high‑purity oil‑free air for laser‑cutting process. If laser‑cutting or high‑purity process air is required, separate downstream refrigerated dryer plus multi‑stage inline filter kit must be configured after compressor outlet.
Direct‑drive specific note: Motor‑to‑air‑end power transfer relies on flexible coupling. The coupling is a wearing consumable component. Aging or mis‑alignment will trigger abnormal vibration and noise. Periodic visual inspection for coupling condition is required for direct‑driven model.
Important performance boundary note: 2.3 m³/min is nominal flow‑rate under standardized ISO‑1217 reference‑conditions. Actual free‑air delivery will decrease when working under high‑ambient‑temperature or high‑altitude location. Site‑operating‑condition data is required for pre‑order performance evaluation to avoid unsatisfactory on‑site capacity.
Unit‑type characteristic reminder: This unit adopts fixed‑speed load‑unload control logic. It shows good reliability under stable full‑load continuous‑running condition. Under heavily fluctuating air‑demand, fixed‑speed design brings relatively higher no‑load power‑consumption compared with VSD variable‑speed drive compressor. This model is recommended for workshops with steady air‑demand; not ideal for sites with frequent large‑range air‑consumption swing.
Field‑service troubleshooting note: Insufficient air‑output or frequent high‑discharge‑temperature alarm does not automatically mean defective screw air‑end. Technicians shall complete upstream inspection workflow: check intake filter clogging → inspect oil‑cooler / radiator fouling → verify thermostatic‑valve working performance, before judging air‑end failure.
Critical buying alert: Model designation JRZ‑20AZ/0.8 alone cannot guarantee perfect site‑fit. Please submit site‑information for our pre‑order technical evaluation: site altitude, maximum summer ambient‑temperature, real‑peak air‑consumption, local power‑supply specification, downstream air‑treatment requirement(dryer / filter or not). Avoid on‑site performance mismatch and production‑downtime.
Customer Buying & Maintenance Priorities
Industrial buyers evaluating 15 kW direct‑drive screw compressor consider multi‑dimensional practical concerns beyond unit price. Below key practical concerns are fully addressed within this page:
1. Site‑fit‑evaluation risk: Nominal flow is reference‑condition value; high‑altitude / high‑temp environment reduces real air‑output; submit site‑data before quotation.
2. Direct‑drive specific awareness: Flexible coupling is wearing consumable; mis‑alignment or aging will cause abnormal vibration & noise; periodic inspection required.
3. Fault‑diagnosis workflow: Avoid direct air‑end condemnation; inspect intake filter, radiator fouling and thermostatic‑valve when facing low‑output / high‑temp alarm.
4. Unit‑type characteristic awareness: Fixed‑speed load‑unload design fits stable continuous‑air‑demand; relatively higher no‑load power‑consumption under fluctuating air‑demand compared with VSD model.
5. System‑matching awareness: Oil‑injected compressor cannot directly deliver high‑purity air for laser‑process; dryer & inline‑filter must be ordered separately.
6. Warranty‑scope clarity: Main‑unit manufacturing‑defect coverage; exclude wearing‑consumables(coupling, filter‑elements, compressor oil); damage caused by wrong‑installation, abnormal‑power‑supply, harsh‑site‑environment; onsite commissioning labor and return‑freight not included.
7. Project‑order support: For system integrators & small‑plant projects, export‑grade fumigated wooden‑crate packing, factory test‑report & shipping‑document support; optional spare‑consumable‑kit.
8. Technical‑backup: Provide installation‑layout hint and routine‑maintenance checklist for on‑site technicians.
Compatibility & Pre‑Order Site‑Condition Checklist
Model:JRZ‑20AZ/0.8
Product Type:Direct‑Drive Single‑Stage Fixed‑Speed Oil‑Injected Screw Air Compressor
Rated Motor Power:15 kW
Nominal Free‑Air Delivery:2.3 m³/min @0.8 MPa(reference‑condition)
Working Pressure:0.8 MPa
Cooling Method:Air‑Cooled
Standard Power‑Supply:380 V / 50 Hz 3‑Phase
Noise Level:78±2 dB(A)
Information we require before quotation:
1. Site altitude & maximum summer ambient‑temperature
2. Actual peak & average compressed‑air consumption
3. Local power‑supply voltage / frequency
4. Down‑stream requirement: whether need refrigerated‑dryer, line‑filters, air‑receiver tank
5. Working‑pattern: 24h continuous‑run or intermittent operation
6. Order‑type: single‑unit replacement / new‑plant project / with spare‑consumable‑kit
Order‑decision reference
‑ Prefer this model: Small‑medium site with stable continuous air‑demand, air‑cooling condition available, moderate budget.
‑ Need further re‑evaluation: High‑altitude, persistent high‑ambient‑temp; large‑range fluctuating air‑consumption; require direct‑supply laser‑cutting high‑purity compressed‑air.
Core Functional Benefits
1. Compact direct‑drive transmission layout
Flexible coupling connects motor and screw air‑end directly, eliminating power loss caused by belt slip. Compact overall footprint, suitable for small‑size factory workshops with limited installation space.
★Note: Flexible coupling belongs to wearing consumable, periodic visual inspection is required.
2. Integrated monitoring panel with maintenance reminder
Control panel displays real‑time system parameters and reminds operators of filter‑element / oil replacement cycles. Operators can easily read running‑hours, oil‑temperature and pressure status for daily‑management.
3. 4‑bearing rotor‑support structure
Four‑bearing supporting design stabilizes rotor operation, lowers vibration amplitude and extends service‑life of core air‑end assembly for long‑time continuous‑running.
4. Air‑cooled integrated cooling package
Integrated air‑cooled radiator assembly, suitable for sites without cooling‑water resource. Sufficient surrounding ventilation clearance must be reserved during installation for reliable heat dissipation.
5. Simplified on‑site deployment
No complex auxiliary infrastructure required. Only solid level foundation and qualified power‑supply are needed for commissioning, fast put‑into‑service for small‑manufacturing workshops.
Technical Specification
| Parameter | Value |
|---|---|
| Model | JRZ‑20AZ/0.8 |
| Type | Direct‑Drive Single‑Stage Fixed‑Speed Screw Air Compressor |
| Rated Motor Power | 15 kW |
| Nominal Free‑Air Delivery | 2.3 m³/min @0.8 MPa (reference‑condition) |
| Rated Working Pressure | 0.8 MPa |
| Cooling Method | Air‑Cooled |
| Motor Rotational Speed | 2980 r/min |
| Standard Power‑Supply | 380 V‑50 Hz 3‑Phase |
| Noise Level | 78±2 dB(A) |
| Transmission Type | Flexible direct‑drive coupling (consumable part) |
| MOQ | 1 Unit |
| Shipment Option | Sea‑freight with export fumigated wooden crate, air‑freight |
| Payment Terms | T/T, PayPal, Western Union |
| Important Remark | Nominal flow reduces at high‑altitude / high‑temp; coupling is consumable; not for direct laser‑cutting high‑purity air output |
Good Customers Reviews

Risk Of Mis‑Application & Wrong‑Site‑Selection
Selecting compressor only by nominal catalog parameters will bring hidden production‑site risk:
1. Ignoring altitude & ambient‑temperature influence: Directly apply catalog 2.3 m³/min value for high‑altitude / hot‑workshop; real‑world air‑output drops and cannot satisfy production‑peak air‑demand.
2. Mis‑application for heavily‑fluctuating air‑demand: Fixed‑speed unit runs with high no‑load power‑consumption under frequent‑changing air‑consumption, leading to extra long‑term electricity‑cost. VSD compressor is better solution for such scenario.
3. Misunderstanding air‑quality performance: Expecting oil‑injected unit to directly deliver laser‑grade high‑purity compressed‑air. Must purchase separate dryer‑filter downstream package for laser‑cutting process.
4. Neglecting direct‑drive coupling inspection: Skipping periodic coupling check; coupling aging / mis‑alignment brings abnormal vibration, noise and mechanical damage risk.
Cost insight: Saving initial budget by mis‑matching compressor model for real‑site working‑conditions may cause insufficient air‑supply, extra power‑consumption and production‑line loss. Compressor selection is system‑level evaluation instead of checking catalog power & flow figures only.
Typical Application Scenarios
This JRZ‑20AZ/0.8 direct‑drive screw compressor is suitable for small‑and‑medium‑industrial‑facilities with relatively stable continuous compressed‑air consumption:
‑ General small‑manufacturing & metal‑processing workshops
‑ Automotive auxiliary assembly, painting auxiliary stations
‑ Plastic‑processing small‑production‑lines
‑ 24‑hour light‑duty continuous‑run compressed‑air‑stations
‑ Compressed‑air system integrators, small‑factory equipment‑renewal projects
Reminder: This oil‑injected unit itself cannot provide laser‑cutting high‑purity compressed‑air. Laser‑process needs matched downstream dryer‑filter package as additional order item. Not recommended for sites with dramatic short‑term air‑consumption fluctuation.
Critical On‑Site Installation, Commissioning & Routine‑Maintenance Guidance
Safety Warning: Strictly perform full LOTO lock‑out‑tag‑out procedure. Cut‑off full power‑supply before opening service panels. Rotating components and hot surfaces present personal‑injury hazard.
1. Pre‑installation site‑preparation
Place unit on solid, level concrete foundation. Reserve sufficient surrounding ventilation clearance for air‑cooled radiator heat dissipation. Guarantee workshop ambient‑temperature within 5‑40℃ range. Confirm on‑site power‑supply matches unit rated specification and complete reliable equipment grounding work. Compressed‑air outlet piping shall adopt pressure‑rated pipeline, install isolation‑valve & check‑valve at compressor outlet.
2. Pre‑start‑up check before commissioning
Check lubricant oil level at sight‑glass; inspect flexible coupling for crack / abnormal gap; check intake filter element condition; confirm cooling‑radiator fin without heavy dust blockage. All safety‑guards must be correctly installed before power‑on.
3. Unit commissioning & baseline‑recording
Power‑on, execute no‑load test‑run firstly, then switch to loaded operation. Monitor discharge‑pressure, oil‑temperature, running‑current under stable full‑load. Record baseline working‑data: actual output pressure, steady oil‑temperature, running‑current for future‑maintenance reference. Inspect unit for abnormal vibration and piping joint for air‑leakage.
4. Key periodic‑maintenance points for direct‑drive model
‑ Periodically inspect flexible coupling condition, replace coupling once crack or obvious aging appears.
‑ Replace intake‑filter / oil‑filter / oil‑separator / compressor‑oil following service‑schedule.
‑ Clean dust fouling on air‑cooled radiator fins to avoid high‑temperature trip.
‑ Check PLC fault history log, resolve early warning fault before breakdown occurs.
5. Troubleshooting hint after commissioning
If compressor suffers low air‑output or frequent high‑oil‑temperature trip: Do NOT judge screw air‑end defective directly. Re‑inspect intake‑filter blockage, radiator fouling and thermostatic‑valve working‑status. Many abnormal‑operation issues root in peripheral components instead of air‑end itself.
Project‑Order & Spare‑Part Planning Guidance
For factory‑maintenance‑teams, compressed‑air‑system integrators:
1. Single‑unit emergency‑replacement: Sea‑freight / air‑freight delivery for small‑factory equipment‑renewal project.
2. Small‑plant new‑construction bulk‑order: Project‑based quotation; export fumigated wooden‑crate packing; provide shipping‑documents & factory run‑test‑report support.
3. Optional combined‑package: Match with intake‑filter / oil‑filter / oil‑separator / flexible coupling consumable‑kit, or supporting refrigerated‑dryer, air‑receiver tank, inline‑filter set for one‑stop compressed‑air‑system solution.
4. Reserved‑stock‑program: We can reserve critical spare‑parts against global supply‑chain fluctuation for regular‑customers.
5. Pre‑shipment‑inspection: Factory running‑test before packing for project‑order; inspection photos available upon request.
Inventory suggestion: Keep critical wearing‑spares(flexible coupling, three filter‑elements) on‑site for 24‑h continuous‑production small‑factory.
Frequently Asked Questions
Q1: Can JRZ‑20AZ/0.8 directly provide high‑purity compressed‑air for laser‑cutting machine?
A: No. This is oil‑injected direct‑drive screw compressor unit. To achieve laser‑grade clean compressed‑air, you need to additionally order downstream refrigerated‑dryer and multi‑stage coalescing filter assembly.
Q2: Catalog shows 2.3 m³/min flow, will I get this flow under high‑altitude / hot‑workshop?
A: 2.3 m³/min is nominal value under standardized reference‑conditions. Actual free‑air‑delivery decreases when site is at high‑altitude or with persistent high‑ambient‑temperature. Please send site‑condition data for our pre‑order performance evaluation.
Q3: Why direct‑drive compressor generates abnormal vibration & noise?
A: Most‑frequent root‑cause: aging / cracked flexible coupling (consumable part); loose mounting‑foot; foundation uneven. Inspect coupling status first instead of suspecting screw air‑end damage directly.
Q4: Is fixed‑speed JRZ‑20AZ/0.8 suitable for workshop with big fluctuation of air‑consumption?
A: Not ideal. Fixed‑speed load‑unload design brings relatively higher no‑load power‑consumption under heavily‑fluctuating air‑demand. VSD variable‑speed screw compressor will be better‑suited solution for such working‑condition. This model is recommended for relatively stable continuous‑air‑demand.
Q5: What regular maintenance items are special for direct‑drive screw compressor?
A: Besides three‑filter & oil replacement, you must periodically inspect flexible coupling for crack and aging. Flexible coupling is wearing consumable part.
Q6: After new unit startup, compressor still shows low air‑output or high‑temperature alarm, is air‑end defective?
A: Not necessarily. Common causes: clogged intake filter, radiator fin fouling, thermostatic‑valve abnormal. Inspect peripheral components before judging air‑end failure.
Q7: What damage situation is excluded under limited product warranty?
A: Limited‑product‑warranty only covers main‑unit manufacturing‑related defects. Excluded: wearing‑consumables(flexible coupling, filter‑elements, compressor‑oil); damage from wrong‑installation, abnormal‑power‑supply, harsh‑site‑environment; onsite commissioning labor and return‑shipment freight are not included.
Request Technical Quotation for JRZ‑20AZ/0.8 15 kW Direct‑Drive Screw Compressor
Fill inquiry‑form with full site‑condition information, downstream‑equipment‑requirement, quantity and destination‑country. Our sales‑engineer will reply quotation and lead‑time promptly.
Hot Tags: jrz-20az/0.8 single stage power frequency screw air compressor, China jrz-20az/0.8 single stage power frequency screw air compressor manufacturers, suppliers

