Tips: Due to the wide variety of air compressor coolers, it may not be possible to display them all on the website. If you need any, please contact us by email or phone.
Product Overview
Part number A11513074 is aftermarket replacement combined integrated air‑oil cooler, factory‑built internal component for CompAir D‑Series, L‑Series, RL‑Series rotary screw air compressors.
Critical technical clarification: This is built‑in combined air‑oil heat exchanger inside compressor cabinet. NO external power‑supply required. It is NOT standalone floor‑mount external radiator. This single unit performs dual cooling tasks: cooling circulating compressor lubricant oil and cooling hot compressed air after air‑end, controlling both oil discharge temperature and compressed‑air outlet temperature.
Important fit‑note: Even with identical part‑number A11513074, there exist different core‑body and flange‑port revision variants. Part‑number alone cannot guarantee perfect fitment. Please submit full CompAir compressor serial‑number and clear photo of old cooler name‑plate label for our pre‑order cross‑verification, to avoid flange‑port mismatch on‑site.
Common field‑failure reminder: Typical fault symptom: compressor high‑temperature shutdown alarm. High‑temp alarm does not automatically mean defective cooler assembly. Most frequent root‑causes: cooler fin surface dust / debris fouling, thermostatic‑valve malfunction, degraded lubricant quality. Inspect these items before judging cooler internal blockage or cross‑leakage. Internal cross‑leak will cause lubricant oil entering compressed‑air circuit.
Commissioning reminder: Mandatory pressure leak test must be completed after cooler replacement, confirm no oil‑side or air‑side leakage before putting compressor back into production.
Critical buying alert: Only referencing part‑number "A11513074" creates fit‑risk. Submit compressor serial‑number plus old‑cooler label photo for compatibility validation and prevent costly production‑downtime.

Customer Buying & Maintenance Priorities
Maintenance technicians sourcing CompAir combined cooler focus on practical real‑site considerations beyond unit price:
1. Component‑function awareness: Built‑in combined air‑oil heat exchanger inside compressor; no power input; dual‑circuit cooling for lubricant and hot compressed air, not standalone external radiator.
2. Fit‑validation risk: Same part‑number may carry flange / core‑body revision variants; compressor serial‑number + old‑cooler label photo required for pre‑order validation.
3. Fault‑diagnosis workflow: High‑temperature shutdown alarm, first inspect fin fouling, thermostatic‑valve and oil‑quality, do not directly replace cooler.
4. Post‑replacement commissioning requirement: Pressure leak test is mandatory after cooler installation.
5. Root‑cause awareness: External dust fouling, internal oil‑sludge scaling, medium‑corrosion are top failure causes, which are operation‑condition related instead of manufacturing defects.
6. Warranty‑scope clarity: Limited‑warranty only covers manufacturing‑related material & welding defects. Damage caused by dust fouling, oil‑sludge scaling, medium‑corrosion, improper installation are excluded. On‑site disassembly / cleaning labor is not covered.
7. Project‑order support: For compressor service fleets; shock‑proof export packing; pre‑shipment pressure‑test photos available on request.
Compatibility & Pre‑Order Verification Checklist
Reference OEM Part‑No:A11513074
Product Type:Aftermarket Replacement Combined Integrated Air‑Oil Cooler (compressor built‑in heat‑exchanger)
Reference applicable compressor series:CompAir D‑Series, L‑Series, RL‑Series rotary screw compressors
Information we require before quotation:
1. Full CompAir compressor serial‑number from machine name‑plate
2. Clear photo of old cooler name‑plate / flange‑port side
3. Brief description of current fault symptom (if for breakdown repair: high‑temp shutdown / oil‑air cross‑leak / external leakage)
4. Working‑site environment: Heavy‑dust workshop / high‑humidity / poor oil‑maintenance history
5. Order‑type: Single breakdown‑repair spare‑part / bulk stock‑up for service fleet
Order‑decision reference
‑ Suitable: Your CompAir screw compressor belongs to D‑Series / L‑Series / RL‑Series and original spare‑part number is A11513074.
‑ Need further re‑evaluation: Machine has heavy history of oil‑sludge, or old cooler flange‑port shows obvious revision difference.
Core Functional Benefits
1. Dual‑circuit combined heat‑exchange design
Single integrated cooler body handles both compressor lubricant oil cooling and post‑process compressed‑air cooling. Controls oil operating temperature meanwhile reduces compressed‑air outlet temperature, matches original CompAir unit thermal management logic.
2. Robust heat‑exchange core for industrial compressor‑room environment
Heat‑exchange core manufactured for continuous heavy‑duty screw compressor running. Resists thermal cycling stress which comes from frequent start‑stop of industrial air station.
3. Direct‑replacement physical dimension & flange‑port layout
Aftermarket unit copies original mounting footprint, oil‑port and air‑port flange arrangement. Fits original compressor cabinet mounting position without extra mechanical modification, provided correct revision variant is matched.
4. Ready for field maintenance environment
Designed for typical service‑shop overhaul scenario; unit comes fully pressure‑tested before shipment.
Technical Specification
| Parameter | Value |
|---|---|
| Reference Part Number | A11513074 |
| Product Type | Aftermarket Replacement Combined Integrated Air‑Oil Cooler (compressor built‑in heat‑exchanger) |
| Working pressure (design) | Up to 10 bar(g) |
| Allowable ambient operating range | ‑20 ℃ ~ +60 ℃ |
| Main material | Aluminum heat‑exchange core + steel flange assembly |
| Important Remark | Built‑in compressor internal component, NO power‑supply; Pressure leak‑test mandatory after replacement; flange / core‑body revision variants exist |
| MOQ | 1 Unit |
| Shipment Option | Sea‑freight with shock‑proof export packing, air‑freight |
| Payment Terms | T/T, PayPal, Western Union |
| Important Warranty Note | Damage from dust fouling, oil‑sludge scaling, medium‑corrosion, wrong‑installation excluded from product warranty; on‑site labor not covered |
Good Customers Reviews

Risk Of Mis‑Application & Wrong‑Selection
Ordering cooler purely based on part‑number A11513074 creates serious hidden operational risk:
1. Mis‑understand component installation form: Treat this built‑in combined cooler as standalone floor‑mount radiator, try to install outside compressor cabinet, thermal‑circuit cannot work correctly.
2. Ignore flange / core‑body revision difference: Only rely on part‑number without compressor serial‑number & old‑cooler photo cross‑check, risk of port‑mismatch during overhaul.
3. Skip post‑install pressure leak‑test: Mount new cooler and run machine directly without leak‑verification, hidden oil‑side or air‑side leakage may occur under full working‑pressure.
4. Mis‑judge cooler failure: When high‑temperature alarm triggers, replace cooler directly without checking fin fouling, thermostatic‑valve and lubricant‑quality; new cooler will also suffer fouling damage under poor‑maintenance site‑condition.
Cost insight: Combined air‑oil cooler is critical thermal‑management spare‑part for screw compressor. Compatibility validation, correct installation and post‑replacement leak test are equally important as hardware quality. Many cooler‑related failures originate from poor site‑maintenance instead of cooler hardware defect.
Typical Application Scenarios
This A11513074 aftermarket combined air‑oil cooler is used for repair‑and‑replacement of matched CompAir D‑Series / L‑Series / RL‑Series rotary screw compressors:
‑ Factory‑site compressor high‑temperature‑fault emergency overhaul repair
‑ Compressor service & rental fleet spare‑parts stocking
‑ General‑industry compressed‑air‑station routine component renewal
Reminder: This is compressor cabinet built‑in combined heat‑exchanger, NOT general‑purpose standalone external radiator for other pneumatic equipment.
Critical On‑Site Installation & Replacement Guidance
Safety Warning: Perform full LOTO lock‑out‑tag‑out procedure. Completely shut‑down compressor, fully depressurize both oil‑circuit and compressed‑air circuit, wait for adequate cooling before cooler disassembly, avoid scald‑injury from hot oil / hot air.
1. Pre‑replacement preparation
Shut‑down, cool‑down and full depressurization of compressor. Take clear photos for original flange‑port orientation, gasket layout and mounting bolt arrangement for reassembly reference. Inspect old cooler: distinguish failure mode (external fin fouling / internal oil‑sludge / cross‑leak / weld crack).
2. Remove existing combined cooler
Disconnect oil‑circuit piping and compressed‑air circuit flanges. Remove mounting fasteners, carefully take out old cooler assembly from compressor cabinet. Clean mounting seat surface, prepare new replacement gaskets / sealing kits.
3. Mount new A11513074 combined cooler
Position new cooler into original cabinet mounting location. Install brand‑new gaskets. Torque‑up flange bolts following correct torque‑sequence specification to prevent gasket‑leakage.
4. Post‑assembly mandatory pressure leak‑test
Restore circuit pressure step‑by‑step. Perform pressure holding leak‑test both on oil‑side and air‑side of cooler assembly, inspect every flange joint for visible leakage. Do NOT skip leak‑test before full‑load compressor startup.
5. Commissioning & functional verification
Start compressor and run under normal working‑condition. Monitor steady‑state oil‑temperature and compressed‑air outlet temperature, confirm temperature stays within machine‑design operating‑window.
6. Troubleshooting hint after replacement
If compressor still reports high‑temperature shutdown after installing new cooler:
Do NOT judge new cooler defective directly. Re‑inspect cooler fin fouling condition, thermostatic‑valve working‑performance and lubricant‑oil quality. Many high‑temp faults root in peripheral components and site‑maintenance status instead of cooler hardware itself.
Spare‑Part Planning Guidance
For factory‑maintenance‑teams and compressor‑service‑contractors:
1. Single emergency spare‑part: Express shipment for on‑site breakdown overhaul repair.
2. Service‑fleet bulk‑stock‑up: Shock‑proof export‑grade packing; pre‑shipment pressure‑test photos can be provided upon project‑order request.
Inventory suggestion: Keep this combined cooler as critical spare‑part for 24‑h continuous‑running CompAir D‑Series / L‑Series / RL‑Series compressors; improve regular fin‑cleaning and oil‑maintenance schedule to reduce cooler‑failure probability.
Frequently Asked Questions
Q1: Can I install A11513074 as an external standalone radiator outside compressor cabinet?
A: No. It is built‑in combined air‑oil cooler inside compressor cabinet. It cannot work as separate floor‑mount external radiator, will break original thermal‑circuit layout.
Q2: After installing new A11513074 cooler, can I run compressor directly?
A: No. Step‑by‑step pressure‑holding leak‑test for oil‑side and air‑side circuit is mandatory before full‑load startup.
Q3: Compressor still triggers high‑temperature alarm after cooler replacement, is new cooler defective?
A: Not necessarily. Please check cooler‑fin fouling, thermostatic‑valve performance and lubricant‑oil‑quality first. Large proportion of high‑temperature events are caused by peripheral components or poor site‑maintenance.
Q4: Which CompAir compressor series does A11513074 fit?
A: Reference fit for CompAir D‑Series, L‑Series, RL‑Series rotary screw compressors. Please provide compressor serial‑number plus old‑cooler photo for cross‑verification because flange / core‑body revision variants exist.
Q5: What failure conditions will be excluded from limited‑product warranty?
A: Limited‑product‑warranty only covers manufacturing‑related material and welding defects. Damage caused by dust fouling, oil‑sludge scaling, medium‑corrosion, improper installation are excluded. On‑site disassembly and cleaning labor cost is not covered.
Q6: Does A11513074 cooler need power‑supply connection?
A: No. This combined air‑oil cooler is pure heat‑exchange hardware without any electrical components, no power‑supply required.
Request Technical Quotation for A11513074 Combined Air‑Oil Cooler
Fill inquiry‑form with compressor serial‑number, old‑cooler photo‑reference, fault‑description(if applicable), quantity and destination‑country. Our sales‑engineer will reply quotation and lead‑time promptly.
Hot Tags: A11513074 Combined Air‑Oil Cooler For CompAir Screw Compressor, China A11513074 Combined Air‑Oil Cooler For CompAir Screw Compressor manufacturers, suppliers, 100000819, 100005313, Compair air cooler spare parts, Oil cooler for compair compressor, A11513274, A11513074
