Product Overview
This product is aftermarket equivalent semi‑synthetic rotary screw compressor lubricant, formulated to match performance requirements of original Kaeser Sigma M‑460 coolant.
Critical clarification: This is compressor lubricant fluid, NOT a complete air‑compressor machine unit.
Important technical distinction:
‑ Kaeser Sigma M‑460: Semi‑synthetic / partial‑synthetic base‑stock, typical reference service interval up to 4000 hours under clean indoor operating‑conditions.
‑ Kaeser Sigma S‑460: Full‑synthetic PAO‑based lubricant, longer service‑life.
Both M‑460 and S‑460 carry ISO VG46 viscosity grade, but base‑chemistry differs. They are NOT directly interchangeable. Always cross‑verify your compressor service manual for the exact required lubricant designation before ordering.
Crucial maintenance reminder: Do NOT mix lubricants of different base‑stock chemistry. If you switch over to this equivalent fluid from other existing oil, you must fully drain out all old residual lubricant from separator tank, oil‑circuit and cooler. Partial draining / direct topping‑up with different oil will trigger chemical reaction, sludge and varnish build‑up, which may lead to air‑end over‑heating and component damage.
Service‑life note: 4000 operating‑hours is only reference benchmark for clean, well‑ventilated indoor workshop. Actual service interval will shorten significantly under high ambient‑temperature, high‑humidity or heavy‑dust environment. For critical 24‑h continuous‑run units, periodic oil‑sample analysis is strongly recommended instead of purely following runtime counter.
Buying‑risk notice: Usage of aftermarket equivalent lubricant may void the original Kaeser OEM machine warranty. End‑user shall evaluate this risk according to local machine‑warranty terms.
Critical buying alert: Search keyword "Sigma M‑460 equivalent" alone cannot guarantee perfect suitability for your machine. Please provide full Kaeser compressor model number plus OEM‑specified lubricant type shown on service manual for our pre‑order technical cross‑verification, to avoid wrong‑fluid selection and costly compressor downtime.
Customer Buying & Maintenance Priorities
Industrial maintenance buyers selecting equivalent Kaeser compressor lubricant care about multi‑dimensional practical points beyond unit price:
1. Lubricant‑type distinction risk: Sigma M‑460 (semi‑synthetic) shall not be confused with Sigma S‑460 (PAO full‑synthetic). Same ISO‑VG46 does not mean interchangeable.
2. Oil‑change workflow awareness: Different base‑stock lubricants cannot be mixed; full draining of old fluid is mandatory during fluid‑switch.
3. Service‑interval logic: Operating‑hour figure is reference‑only; high‑temp / dusty conditions shorten usable life; oil‑sample testing recommended for critical units.
4. Fault‑diagnosis workflow: Sludge, varnish or high oil‑temperature are not always caused by lubricant quality; residual incompatible old‑oil and harsh site‑conditions are common root‑causes.
5. OEM‑warranty awareness: Aftermarket equivalent lubricant may void original compressor OEM warranty; end‑user risk assessment required.
6. Consumable‑product awareness: Compressor lubricant is wearing consumable fluid.
7. Warranty‑scope clarity: Product‑warranty covers manufacturing‑related fluid quality defects only; exclude equipment damages caused by oil‑mixing, incomplete draining and harsh‑site‑operation; onsite labor and return‑freight are not included.
8. Project‑order support: For service‑contractors & large‑plant stock‑up; available MSDS & COA documentation; export‑grade leak‑proof packing options.
Compatibility & Pre‑Order Verification Checklist
Reference OEM designation:Sigma M‑460
Product Type:Semi‑Synthetic Rotary Screw Compressor Lubricant / Coolant (aftermarket equivalent)
Viscosity Grade:ISO VG 46
Information we require before quotation:
1. Full Kaeser compressor model number
2. Exact lubricant requirement printed on machine service manual (confirm M‑460 NOT S‑460)
3. Working‑site environment: indoor / high‑temp / high‑humidity / heavy‑dust / 24‑h continuous‑run
4. Package size requirement: 20 L small‑drum for maintenance or 209 L bulk drum for plant stock‑up
5. Order‑type: single‑maintenance‑order / bulk‑stock for service‑fleet
Order‑decision reference
‑ Suitable: Your machine manual explicitly specifies Kaeser Sigma M‑460 semi‑synthetic coolant.
‑ Need further re‑evaluation: Manual requires Sigma S‑460 PAO full‑synthetic; machine still keeps active OEM warranty; site operates with extreme high‑temperature or heavy moisture.
Core Functional Benefits
1. Semi‑synthetic formulation matched for Kaeser screw compressor circuit
Formulated to replicate core performance profile of original Sigma M‑460. Balanced anti‑oxidation, anti‑wear and anti‑foam properties for rotary‑screw compression cycle. Provides combined functions: lubrication for bearings & rotor profile, compression‑heat dissipation, and internal air‑end sealing.
2. Good water‑separation (demulsibility) performance
Separates condensed water from oil circuit; reduces risk of emulsion formation under high‑humidity workshop conditions.
3. Resistance against sludge & varnish build‑up under normal operating‑conditions
Inhibits oxidation‑by‑product accumulation, helps protect oil‑filter, oil‑separator and thermostatic‑valve from carbon‑deposit fouling, when applied with correct oil‑change procedure.
4. Multiple package options for different‑scale demand
Available in 20 L small drum for single‑unit maintenance work and 209 L bulk drum for large‑factory or compressor‑service‑company stock‑planning.
5. Export‑supporting documentation available
MSDS safety‑data‑sheet and Certificate‑of‑Analysis(COA) can be provided upon request for overseas import customs clearance and site‑safety‑management.
Technical Specification
| Parameter | Value |
|---|---|
| Reference OEM Lubricant | Sigma M‑460 (Kaeser semi‑synthetic compressor coolant) |
| Product Type | Aftermarket equivalent semi‑synthetic screw compressor lubricant |
| Viscosity Grade | ISO VG 46 |
| Reference service‑life | Up to 4000 hrs (clean‑indoor workshop reference‑only) |
| Applicable machine | Matched Kaeser oil‑injected rotary screw compressor requiring Sigma M‑460 |
| Remarks | NOT interchangeable with Sigma S‑460 PAO full‑synthetic; DO NOT mix different base‑stock oils |
| Available Package | 20 L drum / 209 L steel drum |
| MOQ | 1 Drum |
| Shipment Option | Sea‑freight with leak‑proof export packing, air‑freight |
| Payment Terms | T/T, PayPal, Western Union |
| Important Remark | Fully drain old fluid before switching lubricant; aftermarket fluid may void OEM compressor warranty |
Good Customers Reviews
Risk Of Mis‑Application & Wrong‑Selection
Selecting equivalent compressor lubricant only by part‑name "Sigma M‑460 equivalent" creates serious hidden operational risk:
1. Confuse M‑460 with S‑460: Simply match ISO‑VG46 without checking base‑stock chemistry; use semi‑synthetic oil for machine requiring PAO S‑460, causing accelerated sludge‑formation.
2. Mixing different base‑stock lubricants: Top‑up new equivalent oil onto residual old‑fluid without complete draining; chemical incompatibility creates varnish deposits inside oil‑circuit, damaging air‑end and consumable spare‑parts.
3. Blindly follow 4000‑hour runtime: Apply reference service‑life for high‑temperature / high‑moisture workshop; lubricant degrades far ahead of schedule.
4. Warranty overlook: Use aftermarket equivalent fluid while compressor still holds valid OEM warranty; may result in loss of original manufacturer coverage.
Cost insight: Saving cost on substitute lubricant through incorrect selection or improper oil‑change procedure can end‑up with very expensive air‑end overhaul expense. Compressor coolant is a system‑critical consumable, not a simple commodity item.
Typical Application Scenarios
This Sigma M‑460 equivalent semi‑synthetic lubricant is intended for industrial facilities operating matched Kaeser oil‑injected rotary screw compressors whose service‑manual explicitly specifies Sigma M‑460 semi‑synthetic coolant:
‑ General‑manufacturing & metal‑fabrication workshops
‑ Automotive assembly auxiliary compressed‑air stations
‑ Plastic‑processing production‑lines
‑ 24‑hour light‑industry continuous‑run compressed‑air‑plants
‑ Compressor‑service & rental‑companies for maintenance‑stock
Reminder: Not fit for machines requiring Sigma S‑460 full‑synthetic PAO lubricant. Not food‑grade (not FG‑460).
Critical On‑Site Oil‑Change & Operational Guidance
Safety Warning: Perform full LOTO lock‑out‑tag‑out procedure. Allow compressor sufficient cooling before draining hot lubricant. Hot fluid may cause severe scald‑injury.
1. Pre‑oil‑change preparation
Fully shut‑down and cool‑down compressor. Drain out nearly all old lubricant from separator tank, oil‑cooler and oil‑circuit piping.
Mandatory note: If you are switching from a different type of compressor oil, complete draining is required. Partial drain / direct topping‑up will lead to dangerous base‑stock mixing risk.
2. Refill new equivalent lubricant
Fill this Sigma M‑460 equivalent lubricant up to correct sight‑glass level as per compressor manual. Do not overfill. Re‑install all service‑panels.
3. Post‑start‑up commissioning & baseline‑recording
Power‑on and run compressor under stable full‑load for minimum 60‑90 minutes. Monitor oil‑temperature, observe for abnormal foaming. Record baseline operating oil‑temperature for future maintenance reference.
4. Routine‑monitoring recommendation
For critical 24‑h continuous‑running machines, schedule periodic lubricant‑sample testing. Do not rely purely on running‑hour counter to decide oil‑replacement timing.
5. Troubleshooting hint after oil‑change
If varnish, sludge or high oil‑temperature occurs after filling new lubricant:
Do not immediately judge new lubricant defective. Inspect whether old incompatible fluid was incompletely drained; also check operating ambient‑temperature and cooling‑system condition. Many failures root in residual old‑oil or peripheral system instead of new coolant itself.
Spare‑Part & Lubricant Stock‑Planning Guidance
For factory‑maintenance‑teams, compressed‑air‑system integrators and compressor‑service‑contractors:
1. Single‑maintenance‑order: 20 L drum for on‑site compressor oil‑change work.
2. Large‑plant bulk‑stock‑up: 209 L bulk‑drum for multi‑unit periodic‑maintenance, better unit‑cost.
3. Combined‑consumable‑kit: Bundle lubricant together with matched intake‑filter, oil‑filter, oil‑separator for complete overhaul‑package.
4. Reserved‑stock‑program: We can reserve lubricant stock for regular‑customers against global supply‑chain fluctuation.
5. Pre‑shipment‑document support: MSDS and COA documents available upon request for import clearance & site‑safety‑management.
Inventory suggestion: Keep proper lubricant stock onsite for critical 24‑h running Kaeser screw compressors.
Frequently Asked Questions
Q1: Is Sigma M‑460 equivalent interchangeable with Sigma S‑460?
A: No. Although both are ISO VG46, M‑460 is semi‑synthetic and S‑460 is PAO full‑synthetic. Different base‑stock chemistry. Please strictly follow the lubricant type written in your compressor service‑manual.
Q2: Can I top‑up this equivalent oil directly without draining out old compressor oil?
A: Not allowed. Different base‑stock lubricants must not be mixed. You need to fully drain old residual lubricant before refilling this equivalent fluid, otherwise sludge and varnish may form inside oil‑circuit.
Q3: Must I change oil strictly at 4000 running‑hours?
A: 4000‑hour rating is reference‑value under clean‑indoor workshop environment. Service‑life shortens under high‑temperature, high‑humidity or dusty site‑condition. For critical machines oil‑sample analysis is recommended.
Q4: Will using this aftermarket Sigma M‑460 equivalent affect my compressor OEM warranty?
A: Aftermarket substitute lubricant may void original Kaeser OEM machine‑warranty. End‑users should review their local warranty terms and make risk‑assessment by themselves.
Q5: After oil‑change, compressor shows high oil‑temperature or oil sludge, is this lubricant defective?
A: Not necessarily. Common causes: incomplete draining of previous incompatible old oil; poor cooling‑system performance; harsh site‑operating‑environment. Inspect system status before judging lubricant‑quality defect.
Q6: What documents can you provide for import customs clearance?
A: We can supply MSDS (Material Safety Data Sheet) and COA (Certificate of Analysis) upon customer request.
Q7: What damage situations are excluded from limited product warranty?
A: Limited‑product‑warranty only covers lubricant manufacturing‑quality defects. Excluded: equipment damage caused by oil‑mixing, incomplete draining, harsh site‑operating‑conditions; onsite labor and return‑shipment freight are not included.
Request Technical Quotation for Sigma M‑460 Equivalent Lubricant
Fill inquiry‑form with compressor model, required lubricant‑type confirmation, package‑size, quantity and destination‑country. Our sales‑engineer will reply quotation and lead‑time promptly.
Hot Tags: Kaeser Sigma M‑460 Equivalent Semi‑Synthetic Compressor Lubricant, China Kaeser Sigma M‑460 Equivalent Semi‑Synthetic Compressor Lubricant manufacturers, suppliers, Kaeser sigma m 460 equivalent, 9 5409 00010, kaeser sigma fluid s 570, Kaeser Sigma Lubricant S 460, Kaeser s 460 compressor oil

